logo
bandeira

Detalhes do blog

Created with Pixso. Casa Created with Pixso. blog Created with Pixso.

C8060 Cationic PAM Selected for Food Waste Biological Sludge Dewatering

C8060 Cationic PAM Selected for Food Waste Biological Sludge Dewatering

2026-11-19

Bluwat Chemicals evaluated several flocculant grades for biological sludge from a food waste treatment facility. The customer uses a centrifuge for sludge dewatering and needed a polymer that could condition the sludge for solid–liquid separation. Among the products screened in the laboratory, Blufloc C8060 gave the most satisfactory flocculation response. The featured test used a dosage of 60 ppm, and the customer was pleased with the result.

Case Overview

Item Case details
Industry Food waste treatment
Material tested Biological sludge
Customer’s dewatering equipment Centrifuge
Treatment objective Sludge conditioning and solid–liquid separation before mechanical dewatering
Laboratory work Comparative screening of several flocculant grades
Selected product Blufloc C8060 cationic polyacrylamide
Dosage in the featured test 60 ppm
Selection outcome Best flocculation response among the products screened; customer satisfied

The Customer’s Requirement: Prepare Sludge for Centrifuge Dewatering

The sample was biological sludge from a food waste treatment process. The customer’s operating requirement was to separate water from the sludge using the existing centrifuge and produce a dewatered sludge cake.

The laboratory work therefore focused on polymer selection for sludge conditioning. The aim was to identify a product that helped the dispersed solids aggregate into visible flocs, providing a suitable starting point for the customer’s dewatering application.

Reducing the moisture retained in the final cake was an important operating objective. Polymer selection was considered in relation to this objective and the customer’s separation equipment.

Laboratory Screening: C8060 Gave the Best Flocculation Response

Bluwat’s laboratory compared several flocculant grades on the customer’s sludge sample. The team observed the flocculation response after chemical addition and mixing, including the formation and aggregation of sludge flocs and the visible separation of solids from the liquid phase.

Following the comparisons, C8060 was selected as the best-performing grade for flocculation within this screening exercise. In the recorded C8060 test, the reported dosage was 60 ppm. Visible sludge flocs developed during mixing, and the subsequent footage showed the flocculated sludge and the upper liquid layer.

The customer was satisfied with the observed result. Based on the screening and their application experience, Bluwat’s engineers considered C8060 a suitable choice for conditioning this sludge, with the objective of supporting water release and a lower-moisture cake during centrifuge dewatering.

The video documents the laboratory flocculation stage. Final cake moisture and any reduction in moisture content should be confirmed on the operating centrifuge.

Understanding the Turbid Supernatant in the Video

The upper liquid in the laboratory test remained turbid. Clear-water production was outside the scope of this particular screening exercise, which focused on sludge flocculation for the customer’s dewatering requirement.

The visible floc formation was the basis of the laboratory selection reported here. For a complete centrifuge evaluation, cake moisture, solids capture and centrate quality should be assessed together. The laboratory supernatant shown in the video is not a sample of centrifuge centrate.

About Blufloc C8060 Cationic Polyacrylamide

Blufloc C8060 is a high molecular weight, ultra-high-charge cationic polyacrylamide supplied as a white granular powder. Its cationic character and polymer chains help aggregate suitable suspended particles into flocs for separation.

Product characteristic Description
Product name Blufloc C8060
Polymer type Cationic polyacrylamide, or CPAM
Physical form White granular powder
Molecular weight classification High
Charge density classification Ultra high
Solid content ≥89%
Role in this case Biological sludge conditioning for a centrifuge dewatering application

C8060 should be dissolved in clean water before dosing. Bluwat’s published preparation concentration is 0.1–0.5%; the preparation method and operating dose should be matched to the application. The 60 ppm shown in this case is the reported laboratory test dose, rather than a universal dosage for food waste sludge.

Engineering Insight: Match Cationic Charge to the Sludge

Based on Bluwat engineers’ application experience, cationic polyacrylamide is commonly a starting point for biological sludge dewatering. Higher-charge grades can be useful candidates when the sludge requires that charge profile for effective conditioning.

Selecting an appropriate charge density may improve the conditioning response and help support lower cake moisture. However, charge density alone does not determine dewatering performance. The relationship between charge level and cake moisture is not a universal, continuously decreasing trend.

Sludge characteristics, molecular weight, polymer preparation, dose, mixing and centrifuge operating conditions also affect the result. In this case, C8060 earned its selection through comparative testing on the customer’s sample. Its performance should be understood within that application and test scope.

About Bluwat Chemicals

Yixing Bluwat Chemicals Co., Ltd. is a manufacturer and global supplier of water treatment chemicals based in Yixing, Jiangsu, China. With more than two decades of industry experience, three production plants and exports to over 100 countries and regions, Bluwat supplies coagulants and flocculants for industrial and municipal treatment applications.

The company’s product range includes polyacrylamide powders and emulsions, Water Decoloring Agent, PAC, PolyDADMAC, Polyamine and Ferric Sulphate. Its technical support includes laboratory testing and polymer selection based on customers’ actual water and sludge samples.

For sludge dewatering projects, Bluwat can help screen suitable polymer grades in relation to the sludge characteristics, existing equipment and treatment objectives. Customers can share their sludge source, feed solids concentration, current polymer and dosage, centrifuge details and cake moisture target to support a focused evaluation.

Frequently Asked Questions

Why was C8060 selected in this case?

C8060 gave the most satisfactory laboratory flocculation response among the grades screened on this sludge sample. The customer was pleased with the observed result.

Does the turbid supernatant mean the trial failed?

This screening exercise evaluated sludge flocculation for a dewatering application. The customer was satisfied with that result. Centrate quality remains part of a complete centrifuge performance evaluation and should be checked during equipment trials.

Does higher cationic charge always produce a drier sludge cake?

No. The charge level must match the sludge and the process. Higher-charge grades may improve conditioning in suitable applications, while the final cake moisture also depends on polymer properties, dose, preparation and centrifuge operation.

bandeira
Detalhes do blog
Created with Pixso. Casa Created with Pixso. blog Created with Pixso.

C8060 Cationic PAM Selected for Food Waste Biological Sludge Dewatering

C8060 Cationic PAM Selected for Food Waste Biological Sludge Dewatering

Bluwat Chemicals evaluated several flocculant grades for biological sludge from a food waste treatment facility. The customer uses a centrifuge for sludge dewatering and needed a polymer that could condition the sludge for solid–liquid separation. Among the products screened in the laboratory, Blufloc C8060 gave the most satisfactory flocculation response. The featured test used a dosage of 60 ppm, and the customer was pleased with the result.

Case Overview

Item Case details
Industry Food waste treatment
Material tested Biological sludge
Customer’s dewatering equipment Centrifuge
Treatment objective Sludge conditioning and solid–liquid separation before mechanical dewatering
Laboratory work Comparative screening of several flocculant grades
Selected product Blufloc C8060 cationic polyacrylamide
Dosage in the featured test 60 ppm
Selection outcome Best flocculation response among the products screened; customer satisfied

The Customer’s Requirement: Prepare Sludge for Centrifuge Dewatering

The sample was biological sludge from a food waste treatment process. The customer’s operating requirement was to separate water from the sludge using the existing centrifuge and produce a dewatered sludge cake.

The laboratory work therefore focused on polymer selection for sludge conditioning. The aim was to identify a product that helped the dispersed solids aggregate into visible flocs, providing a suitable starting point for the customer’s dewatering application.

Reducing the moisture retained in the final cake was an important operating objective. Polymer selection was considered in relation to this objective and the customer’s separation equipment.

Laboratory Screening: C8060 Gave the Best Flocculation Response

Bluwat’s laboratory compared several flocculant grades on the customer’s sludge sample. The team observed the flocculation response after chemical addition and mixing, including the formation and aggregation of sludge flocs and the visible separation of solids from the liquid phase.

Following the comparisons, C8060 was selected as the best-performing grade for flocculation within this screening exercise. In the recorded C8060 test, the reported dosage was 60 ppm. Visible sludge flocs developed during mixing, and the subsequent footage showed the flocculated sludge and the upper liquid layer.

The customer was satisfied with the observed result. Based on the screening and their application experience, Bluwat’s engineers considered C8060 a suitable choice for conditioning this sludge, with the objective of supporting water release and a lower-moisture cake during centrifuge dewatering.

The video documents the laboratory flocculation stage. Final cake moisture and any reduction in moisture content should be confirmed on the operating centrifuge.

Understanding the Turbid Supernatant in the Video

The upper liquid in the laboratory test remained turbid. Clear-water production was outside the scope of this particular screening exercise, which focused on sludge flocculation for the customer’s dewatering requirement.

The visible floc formation was the basis of the laboratory selection reported here. For a complete centrifuge evaluation, cake moisture, solids capture and centrate quality should be assessed together. The laboratory supernatant shown in the video is not a sample of centrifuge centrate.

About Blufloc C8060 Cationic Polyacrylamide

Blufloc C8060 is a high molecular weight, ultra-high-charge cationic polyacrylamide supplied as a white granular powder. Its cationic character and polymer chains help aggregate suitable suspended particles into flocs for separation.

Product characteristic Description
Product name Blufloc C8060
Polymer type Cationic polyacrylamide, or CPAM
Physical form White granular powder
Molecular weight classification High
Charge density classification Ultra high
Solid content ≥89%
Role in this case Biological sludge conditioning for a centrifuge dewatering application

C8060 should be dissolved in clean water before dosing. Bluwat’s published preparation concentration is 0.1–0.5%; the preparation method and operating dose should be matched to the application. The 60 ppm shown in this case is the reported laboratory test dose, rather than a universal dosage for food waste sludge.

Engineering Insight: Match Cationic Charge to the Sludge

Based on Bluwat engineers’ application experience, cationic polyacrylamide is commonly a starting point for biological sludge dewatering. Higher-charge grades can be useful candidates when the sludge requires that charge profile for effective conditioning.

Selecting an appropriate charge density may improve the conditioning response and help support lower cake moisture. However, charge density alone does not determine dewatering performance. The relationship between charge level and cake moisture is not a universal, continuously decreasing trend.

Sludge characteristics, molecular weight, polymer preparation, dose, mixing and centrifuge operating conditions also affect the result. In this case, C8060 earned its selection through comparative testing on the customer’s sample. Its performance should be understood within that application and test scope.

About Bluwat Chemicals

Yixing Bluwat Chemicals Co., Ltd. is a manufacturer and global supplier of water treatment chemicals based in Yixing, Jiangsu, China. With more than two decades of industry experience, three production plants and exports to over 100 countries and regions, Bluwat supplies coagulants and flocculants for industrial and municipal treatment applications.

The company’s product range includes polyacrylamide powders and emulsions, Water Decoloring Agent, PAC, PolyDADMAC, Polyamine and Ferric Sulphate. Its technical support includes laboratory testing and polymer selection based on customers’ actual water and sludge samples.

For sludge dewatering projects, Bluwat can help screen suitable polymer grades in relation to the sludge characteristics, existing equipment and treatment objectives. Customers can share their sludge source, feed solids concentration, current polymer and dosage, centrifuge details and cake moisture target to support a focused evaluation.

Frequently Asked Questions

Why was C8060 selected in this case?

C8060 gave the most satisfactory laboratory flocculation response among the grades screened on this sludge sample. The customer was pleased with the observed result.

Does the turbid supernatant mean the trial failed?

This screening exercise evaluated sludge flocculation for a dewatering application. The customer was satisfied with that result. Centrate quality remains part of a complete centrifuge performance evaluation and should be checked during equipment trials.

Does higher cationic charge always produce a drier sludge cake?

No. The charge level must match the sludge and the process. Higher-charge grades may improve conditioning in suitable applications, while the final cake moisture also depends on polymer properties, dose, preparation and centrifuge operation.